• This stainless steel lid can be used as a replacement for any BrewMagic V350 system vessel. In fact, it will fit any 12" diameter opening.
  • This kit allows you to fill your Corney keg with beer from your fermenter without opening the top port and risking contamination. Beer will fill your Corney keg from the bottom up through the dip tube on the liquid out side. The kit includes everything shown in the picture except the hose The hose is pictured in order to demonstrate the connections. Hose can be purchased separately. See link below. If you are ready to upgrade from Corneys, see our link below for PubJug.
  • This is the pump we used on BrewMagic systems for many years but it has been discontinued and we can no longer get them. Our recommended replacement is the March 815 High Temperature Pump.  The motor is identical but the volute is much better. It is rated for high temperature and it's made of stainless steel. The recommended replacement pump will require some plumbing on your part to make the hoses fit. Please be aware this is not a drop-in replacement for very old BrewMagic pumps. To determine which style pump is on your BrewMagic system, take a close look at the arrangement of the hose fittings and compare it to the pictures on this site.
  • Oxygen Stone Assembly

    $70.00$130.00
    This is a 0.5 micron stone assembly to aerate your wort as it enters the fermenter. The end of the stone is threaded for easy removal and cleaning. Tri-clamp ready for easy removal and sanitary connection. Sabco uses this assembly on its famous ChillWizard system. This assembly is available in two ways:
    • Stone assembly with tri-clamp connection
    • Complete assembly with 1/4" brass barb along with the inline shut-off valve
  • This is a tri-clamp 90° elbow. The tri-clamp ferrules are 1/2". We use the small version on the top of our Sabco Fermenters to provide a stable mount for valves. We're sure you'll have other interesting ideas for them, too. We make these in two different sizes. The small elbow has a radius of 2 3/16". The large elbow has two different extension lengths. One is 3 3/8" and the other is 4".
  • This kit includes 2 heavy-duty 1.5" tri-clamps along with 2 FDA approved buna gaskets. This size fits 1.5" tri-clamp ferrules with 2" outside diameter.
  • This is a stainless steel type-J thermocouple temperature sensor. It was used on BrewMagic V350 systems until 2013. If you are purchasing this as a replacement for the temperature sensor on your BrewMagic V350 system, please look carefully at what you currently have. If your temperature sensor has 2 wires, purchase this thermocouple. If your sensor has 3 wires, then you need to replace it with an RTD temperature sensor which can also be found on this site.
  • Close any 1.5" tri-clamp ferrule with this clamp. Made of 304 SS. Kit contains:
    • Two 1.5" tri-clamp caps
    • Two 1.5" buna gaskets
  • This little 90° elbow is versatile and you will think of many ways to use it. Specifications:
    • Short radius, approximately 2.75" x 3.5"
    • Includes 1/2" tri-clamp ferrule
    • Will easily connect to any tri-clamp hose
    • Sanitary welded
    • Durable and heavy-duty
  • This is the famous March 815 pump with a GFCI plug added. Rated for boiling temperatures. Includes rugged stainless steel pump housing and built-in bracket, 38" cord and GFCI plug. The March 815 has a larger impeller than most wort pumps which makes it easier to prime and avoids cavitation. Specifications:
    • 115 V AC
    • 1/25 Hp
    • Magnetic drive
    • Ryton impeller
    • Encapsulated ceramic magnet
    • Ceramic shaft
    • thrust bearings
    • Viton o-ring gasket
    • 316 SS hardware
    • Open fan cooled
    • Rated for liquid temperatures up to 250° F
  • 5-ounce tube of high quality gasket adhesive.
  • Get a better view with out adjustable-angle tri-clamp thermometer.  It's adjustable from straight angle all the way to a 60° angle. Features include:
    • Large 3″ dial with bold, bright characters for easy reading
    • Case, bezel and stem in 304 SS
    • Tri-clamp connection in your choice of either 3/4" or 1.5"
    • F° & C° in bold easy-to-read numerals
    • Solid metal construction with stainless probe
    • Hermetically sealed glass lens
    • Easy calibration using screw on back of dial body
    • Accuracy of +/- 1% of full scale
    • Tri-clamp gasket included
  • Replacement flow gasket for PlatePro. These are sold in packages of 6. For example, ordering quantity 1 will give you 6 gaskets
  • Use this adapter to connect any 1/2" or 3/4" tri-clamp to the male end of a garden hose. Use your imagination. This could be handy for connecting a garden hose to just about every Sabco vessel and fitting.
  • This is a set of couplers for ball-lock Corney kegs. Two types are available: threaded and barbed. The barb type will fit any standard 1/4" ID tubing. Simply use a hose clamp. The threaded type, though, is easier to disconnect. Couplers are sold in sets of two as shown in the photo. You’ll get the liquid-out and the gas-in coupling.
  • Use this adapter to modify the female end of a Micromatic shut-off valve to accept your 1/2" tri-clamp hoses. It is also perfect for adding a shut-off valve between two tri-clamp hoses. American D-system keg couplers and shut-off valves utilize a special non-standard thread size. A specific adapter is needed to convert the special thread for use with tri-clamp fittings.
  • You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
  • This is a set of burner orifices for previous versions of BrewMagic with high pressure cast burners as shown in the photo below. This is a set of 3 orifices. These are designed for use with high pressure cast burners only as seen in photo (3/8" Flare x 1/8" MIP elbow). The style of these may vary but the thread sizes do not change. Each orifice is designed specifically for use with propane. High pressure propane sources must be regulated not to exceed 15 psi manifold inlet pressure. High-Pressure-Burner-for-BM If you need orifices for high pressure natural gas, please order this item and submit a note with your order. The note should request Sabco drill out the orifices for natural gas.
  • This is an adapter to connect a 1/2" hose to any 1/2" female pipe thread (NPT). Kit contains one adapter and one hose clamp.
  • Say goodbye to Corneys! Now available in two sizes! 1/2 bbl (about 15.5 gallon) Finally... A serving keg that's economical, easy to clean and compatible with North American Sankey equipment. These are 1/2 barrel kegs with a North American Sankey valve and spear installed in a 4" tri-clamp cap. Please note the Sankey valve is NOT centered in the removable cap. This makes PubJug incompatible with some keg washing equipment. Homebrewers can easily clean these kegs without sacrificing sanitary fittings. Slightly more expensive than Corney kegs but with lots of features:
    • 1/2 bbl (15.5 gal) stainless steel keg sizes available
    • 4" tri-clamp, sanitary cap with tamper resistant closure for safety
    • Includes drop-in, Sankey D-system valve
    • 60 psi, pull-ring pressure relief valve with sanitary o-ring closure so beer does not touch threads
    • Easy to extract the valve and PRV assembly for cleaning - the entire valve assembly can be taken directly to your sink for cleanup
    • Simple upside down, manual, or automated clean out
    Everyone needs a few PubJugs. They are great for bars and restaurants serving many different beverages:
    • Cold-brew coffee
    • Signature cocktails and margaritas in restaurants and bars
    • Wine
  • This LP hose will connect your propane bottle to your BreMagic system. It includes a 1/4" NPT male thread for connecting to the regulator on your BrewMagic V350 system. The other end connects to 20-pound North American LP bottles. Please note this hose will not work with most LP bottles outside North America.
  • This GFCI plug is a safety device, perfect for wet environments. If you have a pump or electric heater being used, it's a good idea to plug it into a GFCI receptacle or use this plug. This plug is rated for 120 Volts, 15 Amps and includes a ground. This plug is the American, grounded, 3-prong version. We use it in our ChillWizard system.
  • Food-grade 3/8" ID tubing designed for beverage use. Very easy to clean. Not approved for boiling temperatures. Tubing is sold in lengths of 10 ft. Example: to buy 20 feet, order a quantity of 2. Great for use as a blowoff tube on your fermenter.
  • Sight Glass

    $80.00$140.00
    Built to Sabco specifications, this sight glass is durable and sanitary. Notice the thickness of top and bottom plates. Easy to take apart for cleaning. Available as either sight glass only or as a kit designed to retrofit older BrewMagic V350 models that used a plastic tube as sight glass on mash inlet. Use with any 1/2" or 3/4" tri-clamp connection. Specifications:
    • Made of 304 SS
    • Overall length = 4.5"
    • Diameter = 2.25"
    • Tube diameter = 3/4"
    The retrofit kit option includes:
    • Sabco sight glass
    • Tri-clamp elbow
    • 2 TC clamps with gaskets
    • 1/2"OD compression union