• This is the pump we used on BrewMagic systems for many years but it has been discontinued and we can no longer get them. Our recommended replacement is the March 815 High Temperature Pump.  The motor is identical but the volute is much better. It is rated for high temperature and it's made of stainless steel. The recommended replacement pump will require some plumbing on your part to make the hoses fit. Please be aware this is not a drop-in replacement for very old BrewMagic pumps. To determine which style pump is on your BrewMagic system, take a close look at the arrangement of the hose fittings and compare it to the pictures on this site.
  • Say goodbye to Corneys!

    Now available in two sizes! 1/6 bbl (about 5 gallon) Finally... A serving keg that's economical, easy to clean and compatible with North American Sankey equipment. 1/6 barrel keg with a North American Sankey valve and spear installed in a 4" tri-clamp cap. Please note the Sankey valve is NOT centered in the removable cap. This makes PubJug incompatible with some keg washing equipment. Homebrewers can easily clean these kegs without sacrificing sanitary fittings. Slightly more expensive than Corney kegs but with lots of features:
    • 1/6 bbl (5.16 gal)
    • 4" tri-clamp, sanitary cap with tamper resistant closure for safety
    • Includes drop-in, Sankey D-system valve
    • 60 psi, pull-ring pressure relief valve with sanitary o-ring closure so beer does not touch threads
    • Easy to extract the valve and PRV assembly for cleaning - the entire valve assembly can be taken directly to your sink for cleanup
    • Simple upside down, manual or automated clean out
    Everyone needs a few PubJugs. They are great for bars and restaurants serving many different beverages:
    • Cold-brew coffee
    • Signature cocktails and margaritas in restaurants and bars
    • Wine
  • Say goodbye to Corneys! Now available in two sizes! 1/2 bbl (about 15.5 gallon) Finally... A serving keg that's economical, easy to clean and compatible with North American Sankey equipment. These are 1/2 barrel kegs with a North American Sankey valve and spear installed in a 4" tri-clamp cap. Please note the Sankey valve is NOT centered in the removable cap. This makes PubJug incompatible with some keg washing equipment. Homebrewers can easily clean these kegs without sacrificing sanitary fittings. Slightly more expensive than Corney kegs but with lots of features:
    • 1/2 bbl (15.5 gal) stainless steel keg sizes available
    • 4" tri-clamp, sanitary cap with tamper resistant closure for safety
    • Includes drop-in, Sankey D-system valve
    • 60 psi, pull-ring pressure relief valve with sanitary o-ring closure so beer does not touch threads
    • Easy to extract the valve and PRV assembly for cleaning - the entire valve assembly can be taken directly to your sink for cleanup
    • Simple upside down, manual, or automated clean out
    Everyone needs a few PubJugs. They are great for bars and restaurants serving many different beverages:
    • Cold-brew coffee
    • Signature cocktails and margaritas in restaurants and bars
    • Wine
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from propane (LP) to natural gas (NG). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • This is the replacement PRV for a Sabco Bright Vessel.
    • 60 psi, non-adjustable
    • Made of nickel-plated brass
    • Includes a pull ring for pressure venting
    • 60 PSI,  Non-Adjustable
    • 1/4" MIP thread
    • Overall size =   1.5" x 1/2" + plus ring
  • Replacement start gasket for PlatePro. These are sold in packages of 2. For example, ordering quantity 1 will give you 2 gaskets.
  • This is an extremely efficient, sanitary plate-and-frame heat exchanger with removable plates. PlatePro has a small frame size which is perfect for professional-level, small-scale breweries. Four-pass efficiency in a small package. Specifications:
    • Dimensions: 16" x 14" x 6"
    • Weight: 48 pounds
    • 304 SS tie-bar frame
    • 3/4" tri-clamp connections for wort
    • 304 SS garden hose thread connections for cooling water
    • 41 removable plates made of 316 SS
    • 9.43 square feet surface area (0.23 square feet per plate)
    • EPDM clip flow gaskets
    • Made in the USA
  • Replacement port gasket for PlatePro. These gaskets come in a package of 2 pieces. For example, ordering quantity 1 will give you 2 gaskets.
  • 5-ounce tube of high quality gasket adhesive.
  • Replacement flow gasket for PlatePro. These are sold in packages of 6. For example, ordering quantity 1 will give you 6 gaskets
  • Oxygen Stone Assembly

    $70.00$130.00
    This is a 0.5 micron stone assembly to aerate your wort as it enters the fermenter. The end of the stone is threaded for easy removal and cleaning. Tri-clamp ready for easy removal and sanitary connection. Sabco uses this assembly on its famous ChillWizard system. This assembly is available in two ways:
    • Stone assembly with tri-clamp connection
    • Complete assembly with 1/4" brass barb along with the inline shut-off valve
  • This is a package of 50 o-rings for keg valves. Color may vary. An essential item for keg maintenance. Use these o-rings along with the correct spiral retaining ring to get out-of-service kegs back to work fast! You should have removal tools and extra valves on hand, as well. Links to these items can be found below. You'll want to make sure you choose the correct o-ring for your keg valve. To do so, first determine if you have drop-in, threaded, or camber valves. We can help:
    • Drop-in valves are installed by dropping the valve into the keyed notches located near the upper edge of the keg neck. Once in place, a stainless, spiral, retaining ring is installed into the upper groove of the keg neck. This holds the valve in position and prevents tampering. Use this o-ring if you have drop-in valves.
    • Camber valves are installed by twisting the valve into the keg neck, then a stainless retaining ring is installed into the upper groove of the keg neck to hold the valve in position. Use this o-ring if you have camber valves.
    • Threaded valves screw into the neck. At the base of the valve is a flat gasket. These valves do not use o-rings. Unfortunately, we no longer carry these flat gaskets. Do NOT order the o-rings on this page.
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from natural gas (NG) to propane (LP). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • This is the famous March 815 pump with a GFCI plug added. Rated for boiling temperatures. Includes rugged stainless steel pump housing and built-in bracket, 38" cord and GFCI plug. The March 815 has a larger impeller than most wort pumps which makes it easier to prime and avoids cavitation. Specifications:
    • 115 V AC
    • 1/25 Hp
    • Magnetic drive
    • Ryton impeller
    • Encapsulated ceramic magnet
    • Ceramic shaft
    • thrust bearings
    • Viton o-ring gasket
    • 316 SS hardware
    • Open fan cooled
    • Rated for liquid temperatures up to 250° F
  • This is the famous March 815 pump with stainless steel housing. The stainless housing is more rugged and rated for 250° F. The larger magnet and impeller design results in higher flow and makes priming easier. Sabco uses this pump on its ChillWizard system. This pump includes a cord but not a plug.
  • These knives help you remove the snap-ring that secures North American keg valves. Ordering quantity of 1 gives you a package of 3 knives. Valve removal tool sold separately. See link below
  • Very useful tool for removal of North American, D-System Micromatic keg valves. Made of solid stainless steel, this removal tool is not messing around. Other useful keg tools and replacement parts are shown below.
  • These spiral, stainless steel lock rings (also known as snap rings or retaining rings) will secure a Micromatic valve into the D-system, drop-in Sankey neck. Keep these on the shelf to ensure your kegs stay in service. These rings are specifically designed to fit certain valve types. Do not substitute them for other designs! Valves can be pressurized and must be properly secured within the keg neck for safety. Remove and install using a valve removal tool and lock ring knife (sold separately, links below) Sold in packages of 25. For example, ordering a quantity of 2 will give you 50 lock rings.
  • This is a box of 2,000 keg caps. Choose your color. Made of durable plastic in bright colors. Vented, too. Sabco's keg caps are the very best available and are very popular nationally. Designed for use with standard Sankey valves and keg necks. They keep dirt and debris out of the keg prior to distribution and use.
  • You probably got a great deal on those used kegs but wouldn't you like to get rid of the name engraved in the dome? Use these labels to cover the engraved name. We make the silver crescents labels using the very same heavy-duty, laminated finish and adhesive that is used for permanent federal warning labels. They are also UV resistant and extremely durable. They can endure heat and cold as well as the caustics and other chemicals. Sold in packages of 100. For example, ordering a quantity of 2 will give you 200 keg engraving shields.
  • This ball valve has a keg coupler thread and is used to stop beer flow from a standard keg coupler. This thread will not fit a 1/2" outlet.
  • This keg coupler works with virtually all American keg valves. Commonly known as D-system. Features include:
    • Stainless steel body for durability and resistance to chemicals
    • Stainless steel handle fork for strength
    • Tin/nickel plated probe is resistant to chemicals and won't chip like chrome
    • Short handle is ideal for 1/2 bbl and 1/6 bbl kegs
    • Includes built-in pressure relief valve (55-65 psi)
    • Includes 3/8" barb for gas port (fits 5/16" ID gas hose)
    • Industry standard beer port
     
  • This adapter will help you connect hose to a threaded ball-lock coupler. Better than hose barbs which distort the hose and leave pockets that are very difficult to clean. Use ball-lock couplers, instead. Kit includes the adapter and a stainless steel hose clamp.
  • This coupler will attach to any US Micromatic keg coupler. It will fit either the gas or beer side. Includes the hose barb, coupler nut and gasket Typically, you will want to choose 3/8" for the gas side and 1/2" for the beer side.