• This is an adapter to connect a 1/2" hose to any 1/2" female pipe thread (NPT). Kit contains one adapter and one hose clamp.
  • This is a set of burner orifices for previous versions of BrewMagic with high pressure cast burners as shown in the photo below. This is a set of 3 orifices. These are designed for use with high pressure cast burners only as seen in photo (3/8" Flare x 1/8" MIP elbow). The style of these may vary but the thread sizes do not change. Each orifice is designed specifically for use with propane. High pressure propane sources must be regulated not to exceed 15 psi manifold inlet pressure. High-Pressure-Burner-for-BM If you need orifices for high pressure natural gas, please order this item and submit a note with your order. The note should request Sabco drill out the orifices for natural gas.
  • Use this adapter to modify the female end of a Micromatic shut-off valve to accept your 1/2" tri-clamp hoses. It is also perfect for adding a shut-off valve between two tri-clamp hoses. American D-system keg couplers and shut-off valves utilize a special non-standard thread size. A specific adapter is needed to convert the special thread for use with tri-clamp fittings.
  • You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
  • This is a set of couplers for ball-lock Corney kegs. Two types are available: threaded and barbed. The barb type will fit any standard 1/4" ID tubing. Simply use a hose clamp. The threaded type, though, is easier to disconnect. Couplers are sold in sets of two as shown in the photo. You’ll get the liquid-out and the gas-in coupling.
  • Get a better view with out adjustable-angle tri-clamp thermometer.  It's adjustable from straight angle all the way to a 60° angle. Features include:
    • Large 3″ dial with bold, bright characters for easy reading
    • Case, bezel and stem in 304 SS
    • Tri-clamp connection in your choice of either 3/4" or 1.5"
    • F° & C° in bold easy-to-read numerals
    • Solid metal construction with stainless probe
    • Hermetically sealed glass lens
    • Easy calibration using screw on back of dial body
    • Accuracy of +/- 1% of full scale
    • Tri-clamp gasket included
  • Use this adapter to connect any 1/2" or 3/4" tri-clamp to the male end of a garden hose. Use your imagination. This could be handy for connecting a garden hose to just about every Sabco vessel and fitting.
  • Replacement flow gasket for PlatePro. These are sold in packages of 6. For example, ordering quantity 1 will give you 6 gaskets
  • 5-ounce tube of high quality gasket adhesive.
  • This is the famous March 815 pump with a GFCI plug added. Rated for boiling temperatures. Includes rugged stainless steel pump housing and built-in bracket, 38" cord and GFCI plug. The March 815 has a larger impeller than most wort pumps which makes it easier to prime and avoids cavitation. Specifications:
    • 115 V AC
    • 1/25 Hp
    • Magnetic drive
    • Ryton impeller
    • Encapsulated ceramic magnet
    • Ceramic shaft
    • thrust bearings
    • Viton o-ring gasket
    • 316 SS hardware
    • Open fan cooled
    • Rated for liquid temperatures up to 250° F
  • Close any 1.5" tri-clamp ferrule with this clamp. Made of 304 SS. Kit contains:
    • Two 1.5" tri-clamp caps
    • Two 1.5" buna gaskets
  • This little 90° elbow is versatile and you will think of many ways to use it. Specifications:
    • Short radius, approximately 2.75" x 3.5"
    • Includes 1/2" tri-clamp ferrule
    • Will easily connect to any tri-clamp hose
    • Sanitary welded
    • Durable and heavy-duty
  • This is a stainless steel type-J thermocouple temperature sensor. It was used on BrewMagic V350 systems until 2013. If you are purchasing this as a replacement for the temperature sensor on your BrewMagic V350 system, please look carefully at what you currently have. If your temperature sensor has 2 wires, purchase this thermocouple. If your sensor has 3 wires, then you need to replace it with an RTD temperature sensor which can also be found on this site.
  • This kit includes 2 heavy-duty 1.5" tri-clamps along with 2 FDA approved buna gaskets. This size fits 1.5" tri-clamp ferrules with 2" outside diameter.
  • Oxygen Stone Assembly

    $70.00$130.00
    This is a 0.5 micron stone assembly to aerate your wort as it enters the fermenter. The end of the stone is threaded for easy removal and cleaning. Tri-clamp ready for easy removal and sanitary connection. Sabco uses this assembly on its famous ChillWizard system. This assembly is available in two ways:
    • Stone assembly with tri-clamp connection
    • Complete assembly with 1/4" brass barb along with the inline shut-off valve
  • This is a tri-clamp 90° elbow. The tri-clamp ferrules are 1/2". We use the small version on the top of our Sabco Fermenters to provide a stable mount for valves. We're sure you'll have other interesting ideas for them, too. We make these in two different sizes. The small elbow has a radius of 2 3/16". The large elbow has two different extension lengths. One is 3 3/8" and the other is 4".
  • This is the pump we used on BrewMagic systems for many years but it has been discontinued and we can no longer get them. Our recommended replacement is the March 815 High Temperature Pump.  The motor is identical but the volute is much better. It is rated for high temperature and it's made of stainless steel. The recommended replacement pump will require some plumbing on your part to make the hoses fit. Please be aware this is not a drop-in replacement for very old BrewMagic pumps. To determine which style pump is on your BrewMagic system, take a close look at the arrangement of the hose fittings and compare it to the pictures on this site.
  • This kit allows you to fill your Corney keg with beer from your fermenter without opening the top port and risking contamination. Beer will fill your Corney keg from the bottom up through the dip tube on the liquid out side. The kit includes everything shown in the picture except the hose The hose is pictured in order to demonstrate the connections. Hose can be purchased separately. See link below. If you are ready to upgrade from Corneys, see our link below for PubJug.
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from propane (LP) to natural gas (NG). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • This stainless steel lid can be used as a replacement for any BrewMagic V350 system vessel. In fact, it will fit any 12" diameter opening.
  • Do you have a false bottom in your BrewMagic V350 kettle? Consider converting to a whirlpool siphon. It's easy to manually create a whirlpool in the small kettle on a BrewMagic V350 system if you have this tri-clamp siphon. After knockout, rotate your spoon around the perimeter of the kettle to turn the wort and create a cone of trub. You'll leave that stuff behind instead of clogging up your ChillWizard or transferring it to your fermenter. Made of 304 SS and sanitary welded with a tri-clamp connection.
  • This is a replacement carbonation stone for use with the Sabco Carb Wand. Porous metal design  .005  (1/2 micron) 1/8" FIP connection Made of 304 SS
  • This is the RTD temperature sensor used on all current BrewMagic systems. It was also used on V350 systems beginning in 2013. RTD sensors provide accurate temperature data to digital controllers such as those used on BrewMagic systems. These RTD sensors have the following specifications:
    • Made of 304 SS
    • 100 ohms
    • 3-wire design for increased accuracy
    • 1/4" diameter
    • 3" probe length
    • Relief spring at probe to prevent damage
    • 12 feet of armored cable for durability in harsh environments
    This RTD (resistance temperature detector) provides accurate and stable information to your V350 Brew-Magic controller.  This will replace the existing one in your Brew-Magic System If you are purchasing this as a replacement for the temperature sensor on your BrewMagic, please look carefully at what you currently have. If your temperature sensor has 3 wires, purchase this RTD. If your sensor has 2 wires, then you need to replace it with a type-J thermocouple which can also be found on this site.
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from natural gas (NG) to propane (LP). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.