[wcas-search-form]

  • Close any 1.5" tri-clamp ferrule with this clamp. Made of 304 SS. Kit contains:
    • Two 1.5" tri-clamp caps
    • Two 1.5" buna gaskets
  • This is a package of 3 buna gaskets for tri-clamps. Use these gaskets to fit ferrules with 2" OD. This ferrule size is commonly used with both 1" and 1.5" ID tri-clamp fittings. These are the very same gaskets you will find on BrewMagic equipment with thermometer connections. Sold in packages of 3. For example, ordering quantity of 2 will give you 6 gaskets.
  • This kit includes 2 heavy-duty 1.5" tri-clamps along with 2 FDA approved buna gaskets. This size fits 1.5" tri-clamp ferrules with 2" outside diameter.
  • These are band new, drop-in, D-system, twin-lug American Sankey beer keg valves. They come equipped with o-ring. Keep a few of these backup valves on hand to minimize out-of-service kegs.
    These are 1/2 barrel (15.5 gal) standard keg length (21.75") but can be cut down to fit smaller capacity kegs.
    Sold in packages of 10 valves. For example, ordering a quantity of 2 will give you 20 valves.
  • This is a package of 5 buna gaskets for tri-clamps. Choose size 1/2" or 3/4" ID hose sizes below. These are the very same gaskets that you will find on most tri-clamp connections on Sabco equipment.
  • Use this to connect any 1/2" threaded male outlet to your 1/2" ID hose. Perfect for connecting most pump motors. Made of 304 SS. Includes adapter and SS hose clamp.
  • Close any 1/2" or 3/4" tri-clamp ferrule with this cap. Made of 304 SS. Kit contains:
    • 2 tri-clamp caps
    • 2 buna gaskets
  • Sabco jet burners are not messing around. This burner is rated at 60,000 BTU. It measures 5 5/8" in diameter, weighs 2.6 pounds and has a built-in bracket for adapting igniters. Gas pipe connection is 3/8" NPT. Designed for low pressure. Natural gas supplies are typically already low pressure but bottled propane will need to be regulated below 11" water column for these burners.  
  • This stainless steel lid can be used as a replacement for any BrewMagic V350 system vessel. In fact, it will fit any 12" diameter opening.
  • It's always a good idea to have spare parts on hand. See links below for these other PlatePro parts. These plates are sold in packages of 2. For example, ordering quantity 1 will give you 2 plates.
  • It's always a good idea to have spare parts on hand. See links below for these other PlatePro parts. These plates are sold in packs of 2. For example, ordering quantity 1 will give you 2 plates.
  • Sabco jet burners are not messing around. This burner is rated at 120,000 BTU. It measures 8" in diameter, weighs 4.6 pounds and has 2 types of built-in brackets for adapting igniters. Gas pipe connection is 1/2" NPT. Designed for low pressure. Natural gas supplies are typically already low pressure but bottled propane will need to be regulated below 11" water column for these burners.
  • This is a complete Tri-Clamp assembly for performing your own installation of a 4" sanitary port on any vessel. Includes:
    • 4" tri-clamp long ferrule, 304 SS
    • 4" tri-clamp with heavy turn bolt, 304 SS
    • 4" tri-clamp cap, 304 SS
    • 4" buna tri-clamp gasket
  • 4″ Sankey Tri-Clamp Cap

    $110.00$135.00
    Easily convert your 4" tri-clamp storage vessels to a standard D-system Sankey for simply cleaning or dispensing. This specially designed cap allows inspection of the interior with the simple removal of the tri-clamp. Take advantage of the convenient Sankey valve and then quickly extract the entire valve assembly to easily clean the inside. Important Note: A PRV (pressure relief valve) is needed for your coupler or tank. Serious personal injury may result if your pressure vessel does not include this.
  • This 4" tri-clamp cap can be used to upgrade an older Sabco Fermenter to the current design. Two sanitary ports in the cap give you lots of options. On our Sabco Fermenter we use one for blow-off. The other port can be used to inject oxygen or COwith our Carb Wand. This lets you use your fermenter as a bright tank. Pro tip: Get this cap along with the Carb Wand and Dirty Gauge (links below) to carbonate very quickly right inside your fermenter or bright tank. This cap also includes 2 tri-clamps, 2 caps and 2 gaskets.
  • This is a package of 3 buna gaskets for 4" tri-clamps. These are the gaskets Sabco uses on products such as PubJug, Sabco Fermenters and Sabco Bright Vessels Sold in packages of 3. For example, ordering quantity of 2 will give you 6 gaskets.
  • This kit includes a 4" tri-clamp and a buna gasket. Clamp is solid 304 SS with a heavy-turn bolt.
  • It's always a good idea to have spare parts on hand. See links below for these other PlatePro parts. These plates are sold in packs of 6. For example, ordering quantity 1 will give you 6 plates.
  • 8" Tri-Clamp Buna Gasket. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order of this item.
  • 8" Tri-Clamp compatible cap. All stainless. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order of this item.
  • 8" Tri-Clamp. All stainless. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order for clearance items.
  • 8" Tri-Clamp Compatible Long Ferrule. All stainless. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order of this item.
  • This is a swivel adapter to connect a 1/2" hose to any 1/2" male pipe thread (NPT). Use it to connect a hose to the inlet or outlet of a pump with 1/2" MIP inlet or outlet threads. The large grip-style nut makes it easy to snug up the adapter by hand without tools. This eliminates the possibility of damaging the o-ring by over-tightening with a wrench. This also allows an easy disconnect for cleaning. Kit contains one adapter (grip & tailpiece), o-ring, and hose clamp.
  • This is an adapter to connect a 1/2" hose to any 1/2" female pipe thread (NPT). Kit contains one adapter and one hose clamp.
  • This adapter will help you convert the threaded fittings on your pump to sanitary tri-clamp. Once you have converted your pump to tri-clamp fittings you'll be able to easily connect and disconnect your hoses. Package of 1 adapter. We know the picture shows 2 but they are sold individually.
  • This adapter will fit a 1/2" female NPT connection and convert it to tri-clamp. Easily connect and disconnect hoses once you convert. Adapters are sold individually.
  • Use this adapter to modify the female end of a Micromatic shut-off valve to accept your 1/2" tri-clamp hoses. It is also perfect for adding a shut-off valve between two tri-clamp hoses. American D-system keg couplers and shut-off valves utilize a special non-standard thread size. A specific adapter is needed to convert the special thread for use with tri-clamp fittings.
  • Use this adapter to modify a keg coupler to accept your 1/2" tri-clamp hoses. Includes tailpiece and black buna gasket. American D-system keg couplers and shut-off valves utilize a special non-standard thread size. A specific adapter is needed to convert the special thread for use with tri-clamp fittings.
  • These adapters are perfect for making any 3/4" to  1=1/2" TC connection
  • Use this adapter to connect any 1/2" or 3/4" tri-clamp to the male end of a garden hose. Use your imagination. This could be handy for connecting a garden hose to just about every Sabco vessel and fitting.
  • Get a better view with out adjustable-angle tri-clamp thermometer.  It's adjustable from straight angle all the way to a 60° angle. Features include:
    • Large 3″ dial with bold, bright characters for easy reading
    • Case, bezel and stem in 304 SS
    • Tri-clamp connection in your choice of either 3/4" or 1.5"
    • F° & C° in bold easy-to-read numerals
    • Solid metal construction with stainless probe
    • Hermetically sealed glass lens
    • Easy calibration using screw on back of dial body
    • Accuracy of +/- 1% of full scale
    • Tri-clamp gasket included
  • This is a set of couplers for ball-lock Corney kegs. Two types are available: threaded and barbed. The barb type will fit any standard 1/4" ID tubing. Simply use a hose clamp. The threaded type, though, is easier to disconnect. Couplers are sold in sets of two as shown in the photo. You’ll get the liquid-out and the gas-in coupling.
  • Designed for use with household natural gas pressure this cast-iron banjo style burner will produce approx. 30,000 Btu of heating energy. Perfect for your 10-30 gallon mash tun or outdoor cooking. This unit comes with a standard natural gas orifice but can be exchanged for an LP gas orifice. Choose option above. Be advised that when using bottle LP gas that you will need a regulator that will reduce inlet pressure to approx. 11" WC (water column) for best combustion efficiency.
    • 9.2" overall length without orifice
    • 6" burner diameter
    • 4 lbs. cast iron
    • Bracket screw located on the center back side
    • Orifice has 3/8" brass elbow flared connection to fit most gas supply hosing
    • Variable air-mix vent which is used to tune the incoming air and adjust for the most efficient flame
  • This bleeder valve helps you easily prime your magnetic drive pump. Use the bleeder valve to vent air trapped in the hose on the inlet side of the pump. Sabco includes this valve with each ChillWizard chilling system. We didn't always include it, though, so if you have an older ChillWizard, this is a great upgrade. Made of stainless steel. See link below to order high-temperature silicone tubing to connect boil kettle to pump.
  • BrewMagic® Pilot RIMS System

    $7,200.00$9,200.00
    Have questions or need info on any of our great BrewMagic brewing systems?   Contact Matt directly at (419) 345-8290, via call or text, and he can assist with anything you may need to get started. BrewMagic Pilot is available in electric or gas. Choose your size - 20 gallons or 30 gallons. It's still built on the tried-and-true BrewMagic platform but we have gone all stainless, increased batch capacity, boosted the pump and enlarged the touch-screen. The system is ideal for:
    • Serious home brewers
    • Friends who brew together and each want to keep 10 or 12 gallons
    • Pilot brewing and recipe development
    • Nano brewery startups
    • College and university brewing science programs
    Insanely high quality and repeatability have been our claim to fame for almost 30 years. We produced the first commercial-grade RIMS system and have thousands of BrewMagic™ systems in service around the world. Our reputation precedes us, so you can understand why we were so careful about introducing this new system. Our goal was to increase capacity and add features without sacrificing anything. BrewMagic™ Pilot is the result.
    • RIMS (recirculating infusion mash system)
    • All-stainless construction
    • 3-vessel design – Hot liquor, mash tun and boil kettle
    • Sanitary, food-grade welding without threaded fittings
    • 80,000 BTU low-pressure jet burners with electronic igniters
    • Tri-clamp fittings, no soft plumbing
    • Precise temperature control without scorching or caramelization
    • Brew 10-25 gallon batch sizes
    • Digital temperature readout on all 3 vessels
    • 7-inch color touch-screen control
    • Powerful March TE pump
    • Sight glass for mash
    • Recipe storage for mash and boil with visual and audible prompts
    • Network and WiFi capable
    If you’d prefer a full written quote from one of our brewing experts click here to customize your system or call 419-531-5347 to speak with a brewing system expert today.
       
  • Call or text Matt directly at 419-345-8290 with questions.
    BrewMagic Pilot is a 56-gallon system built on the tried-and-true BrewMagic platform. We have gone all stainless, increased batch capacity, boosted the pump and enlarged the touch-screen. The system is ideal for:
    • Startup breweries
    • Brewpubs
    • Pilot brewing and recipe development
    • Nano brewery startups
    • College and university brewing science programs
    Insanely high quality and repeatability have been our claim to fame for almost 30 years. We produced the first commercial-grade RIMS system and have thousands of BrewMagic™ systems in service around the world. BrewMagic® Pro includes the following features:
    • RIMS (recirculating infusion mash system)
    • All-stainless construction
    • 3-vessel design – Hot liquor, mash tun and boil kettle
    • Sanitary, food-grade welding without threaded fittings
    • 80,000 BTU low-pressure jet burners with electronic igniters
    • Tri-clamp fittings, no soft plumbing
    • Precise temperature control without scorching or caramelization
    • Brew 10-50 gallon batch sizes
    • Digital temperature readout on all 3 vessels
    • 7-inch color touch-screen control
    • 2 powerful March TE pumps
    • Sight glass for mash
    • Recipe storage for mash and boil with visual and audible prompts
    • Network and WiFi capable
     
  • You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
  • This is a replacement carbonation stone for use with the Sabco Carb Wand. Porous metal design  .005  (1/2 micron) 1/8" FIP connection Made of 304 SS
  • ChillWizard System

    $990.00$1,090.00
    The ChillWizard system includes everything you need for pumping, chilling and oxygen injection all in one compact, portable unit. High efficiency. Easy cleaning. You'll love it. Features include:
    • Clean in place using the pump
    • Diffusion stone to inject oxygen as wort flows through the chiller
    • Thermometer on the exit side displays wort temperature
    • Adjustable flow rate
    • Pump is capable of sending wort uphill to your fermenter
    • Easily disassembled for periodic deep clean
    • Easily reverse flow through plate chiller for backflushing
    • All built on a compact frame with handle
    • GFCI plug for safety in wet environments
  • This LP hose will connect your propane bottle to your BreMagic system. It includes a 1/4" NPT male thread for connecting to the regulator on your BrewMagic V350 system. The other end connects to 20-pound North American LP bottles. Please note this hose will not work with most LP bottles outside North America.
  • These Federal Warning labels are required by law and have been approved for use on beer kegs nationally. We use an incredibly strong adhesive for stainless application and a thick laminated surface. These stay put even in harsh caustic conditions. 3 3/8" x 1 7/16" with black text on white background. Sold in packages of 50. For example, ordering a quantity of 2 will give you 100 labels.
  • This GFCI plug is a safety device, perfect for wet environments. If you have a pump or electric heater being used, it's a good idea to plug it into a GFCI receptacle or use this plug. This plug is rated for 120 Volts, 15 Amps and includes a ground. This plug is the American, grounded, 3-prong version. We use it in our ChillWizard system.
  • This is a set of burner orifices for previous versions of BrewMagic with high pressure cast burners as shown in the photo below. This is a set of 3 orifices. These are designed for use with high pressure cast burners only as seen in photo (3/8" Flare x 1/8" MIP elbow). The style of these may vary but the thread sizes do not change. Each orifice is designed specifically for use with propane. High pressure propane sources must be regulated not to exceed 15 psi manifold inlet pressure. High-Pressure-Burner-for-BM If you need orifices for high pressure natural gas, please order this item and submit a note with your order. The note should request Sabco drill out the orifices for natural gas.
  • This coupler will attach to any US Micromatic keg coupler. It will fit either the gas or beer side. Includes the hose barb, coupler nut and gasket Typically, you will want to choose 3/8" for the gas side and 1/2" for the beer side.
  • This adapter will help you connect hose to a threaded ball-lock coupler. Better than hose barbs which distort the hose and leave pockets that are very difficult to clean. Use ball-lock couplers, instead. Kit includes the adapter and a stainless steel hose clamp.
  • This keg coupler works with virtually all American keg valves. Commonly known as D-system. Features include:
    • Stainless steel body for durability and resistance to chemicals
    • Stainless steel handle fork for strength
    • Tin/nickel plated probe is resistant to chemicals and won't chip like chrome
    • Short handle is ideal for 1/2 bbl and 1/6 bbl kegs
    • Includes built-in pressure relief valve (55-65 psi)
    • Includes 3/8" barb for gas port (fits 5/16" ID gas hose)
    • Industry standard beer port
     
  • This ball valve has a keg coupler thread and is used to stop beer flow from a standard keg coupler. This thread will not fit a 1/2" outlet.
  • You probably got a great deal on those used kegs but wouldn't you like to get rid of the name engraved in the dome? Use these labels to cover the engraved name. We make the silver crescents labels using the very same heavy-duty, laminated finish and adhesive that is used for permanent federal warning labels. They are also UV resistant and extremely durable. They can endure heat and cold as well as the caustics and other chemicals. Sold in packages of 100. For example, ordering a quantity of 2 will give you 200 keg engraving shields.
  • This is a box of 2,000 keg caps. Choose your color. Made of durable plastic in bright colors. Vented, too. Sabco's keg caps are the very best available and are very popular nationally. Designed for use with standard Sankey valves and keg necks. They keep dirt and debris out of the keg prior to distribution and use.
  • These spiral, stainless steel lock rings (also known as snap rings or retaining rings) will secure a Micromatic valve into the D-system, drop-in Sankey neck. Keep these on the shelf to ensure your kegs stay in service. These rings are specifically designed to fit certain valve types. Do not substitute them for other designs! Valves can be pressurized and must be properly secured within the keg neck for safety. Remove and install using a valve removal tool and lock ring knife (sold separately, links below) Sold in packages of 25. For example, ordering a quantity of 2 will give you 50 lock rings.
  • Very useful tool for removal of North American, D-System Micromatic keg valves. Made of solid stainless steel, this removal tool is not messing around. Other useful keg tools and replacement parts are shown below.
  • These knives help you remove the snap-ring that secures North American keg valves. Ordering quantity of 1 gives you a package of 3 knives. Valve removal tool sold separately. See link below
  • This is the famous March 815 pump with stainless steel housing. The stainless housing is more rugged and rated for 250° F. The larger magnet and impeller design results in higher flow and makes priming easier. Sabco uses this pump on its ChillWizard system. This pump includes a cord but not a plug.
  • This is the famous March 815 pump with a GFCI plug added. Rated for boiling temperatures. Includes rugged stainless steel pump housing and built-in bracket, 38" cord and GFCI plug. The March 815 has a larger impeller than most wort pumps which makes it easier to prime and avoids cavitation. Specifications:
    • 115 V AC
    • 1/25 Hp
    • Magnetic drive
    • Ryton impeller
    • Encapsulated ceramic magnet
    • Ceramic shaft
    • thrust bearings
    • Viton o-ring gasket
    • 316 SS hardware
    • Open fan cooled
    • Rated for liquid temperatures up to 250° F
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from natural gas (NG) to propane (LP). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • This is a package of 50 o-rings for keg valves. Color may vary. An essential item for keg maintenance. Use these o-rings along with the correct spiral retaining ring to get out-of-service kegs back to work fast! You should have removal tools and extra valves on hand, as well. Links to these items can be found below. You'll want to make sure you choose the correct o-ring for your keg valve. To do so, first determine if you have drop-in, threaded, or camber valves. We can help:
    • Drop-in valves are installed by dropping the valve into the keyed notches located near the upper edge of the keg neck. Once in place, a stainless, spiral, retaining ring is installed into the upper groove of the keg neck. This holds the valve in position and prevents tampering. Use this o-ring if you have drop-in valves.
    • Camber valves are installed by twisting the valve into the keg neck, then a stainless retaining ring is installed into the upper groove of the keg neck to hold the valve in position. Use this o-ring if you have camber valves.
    • Threaded valves screw into the neck. At the base of the valve is a flat gasket. These valves do not use o-rings. Unfortunately, we no longer carry these flat gaskets. Do NOT order the o-rings on this page.
  • Oxygen Stone Assembly

    $70.00$130.00
    This is a 0.5 micron stone assembly to aerate your wort as it enters the fermenter. The end of the stone is threaded for easy removal and cleaning. Tri-clamp ready for easy removal and sanitary connection. Sabco uses this assembly on its famous ChillWizard system. This assembly is available in two ways:
    • Stone assembly with tri-clamp connection
    • Complete assembly with 1/4" brass barb along with the inline shut-off valve
  • Replacement flow gasket for PlatePro. These are sold in packages of 6. For example, ordering quantity 1 will give you 6 gaskets
  • 5-ounce tube of high quality gasket adhesive.
  • Replacement port gasket for PlatePro. These gaskets come in a package of 2 pieces. For example, ordering quantity 1 will give you 2 gaskets.
  • This is an extremely efficient, sanitary plate-and-frame heat exchanger with removable plates. PlatePro has a small frame size which is perfect for professional-level, small-scale breweries. Four-pass efficiency in a small package. Specifications:
    • Dimensions: 16" x 14" x 6"
    • Weight: 48 pounds
    • 304 SS tie-bar frame
    • 3/4" tri-clamp connections for wort
    • 304 SS garden hose thread connections for cooling water
    • 41 removable plates made of 316 SS
    • 9.43 square feet surface area (0.23 square feet per plate)
    • EPDM clip flow gaskets
    • Made in the USA
  • Replacement start gasket for PlatePro. These are sold in packages of 2. For example, ordering quantity 1 will give you 2 gaskets.
  • This is the replacement PRV for a Sabco Bright Vessel.
    • 60 psi, non-adjustable
    • Made of nickel-plated brass
    • Includes a pull ring for pressure venting
    • 60 PSI,  Non-Adjustable
    • 1/4" MIP thread
    • Overall size =   1.5" x 1/2" + plus ring
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from propane (LP) to natural gas (NG). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • Say goodbye to Corneys!

    Finally... A 5-gallon serving keg that's economical, easy to clean and compatible with North American Sankey equipment. This is a 1/6 barrel keg with a North American Sankey valve and spear installed in a 4" tri-clamp cap. Homebrewers can easily clean these kegs without sacrificing sanitary fittings. Slightly more expensive than Corney kegs but with lots of features:
    • 1/6 bbl (5.16 gal) stainless steel keg
    • 4" tri-clamp, sanitary cap with tamper resistant closure for safety
    • Includes drop-in, Sankey D-system valve
    • 60 psi, pull-ring pressure relief valve with sanitary o-ring closure so beer does not touch threads
    • Easy to extract the valve and PRV assembly for cleaning - the entire valve assembly can be taken directly to your sink for cleanup
    • Simple upside down, manual or automated clean out
    Everyone needs a few PubJugs. They are great for bars and restaurants serving many different beverages:
    • Cold-brew coffee
    • Signature cocktails and margaritas in restaurants and bars
    • Wine
  • This is the pump we used on BrewMagic systems for many years but it has been discontinued and we can no longer get them. Our recommended replacement is the March 815 High Temperature Pump.  The motor is identical but the volute is much better. It is rated for high temperature and it's made of stainless steel. The recommended replacement pump will require some plumbing on your part to make the hoses fit. Please be aware this is not a drop-in replacement for very old BrewMagic pumps. To determine which style pump is on your BrewMagic system, take a close look at the arrangement of the hose fittings and compare it to the pictures on this site.
  • Food-grade 3/8" ID tubing designed for beverage use. Very easy to clean. Not approved for boiling temperatures. Tubing is sold in lengths of 10 ft. Example: to buy 20 feet, order a quantity of 2. Great for use as a blowoff tube on your fermenter.
  • This braided hose is great. Non-toxic, thick, resists kinks. Suggested only for temperatures between 25° and 175° F. Sold in lengths of 10 feet. For example, ordering quantity of 2 will give you 20 feet of hose.
  • Stainless steel chamber for low-density heating element. No threads. All sanitary welding by the best welders around. Constructed of 304 SS, 15.13"L, 1.38"ID, 1.5" tri-clamp connection. Wort in/out tubing is 0.5"OD. Heating element sold separately. See link below.
  • This is the RTD temperature sensor used on all current BrewMagic systems. It was also used on V350 systems beginning in 2013. RTD sensors provide accurate temperature data to digital controllers such as those used on BrewMagic systems. These RTD sensors have the following specifications:
    • Made of 304 SS
    • 100 ohms
    • 3-wire design for increased accuracy
    • 1/4" diameter
    • 3" probe length
    • Relief spring at probe to prevent damage
    • 12 feet of armored cable for durability in harsh environments
    This RTD (resistance temperature detector) provides accurate and stable information to your V350 Brew-Magic controller.  This will replace the existing one in your Brew-Magic System If you are purchasing this as a replacement for the temperature sensor on your BrewMagic, please look carefully at what you currently have. If your temperature sensor has 3 wires, purchase this RTD. If your sensor has 2 wires, then you need to replace it with a type-J thermocouple which can also be found on this site.
  • The Sabco Bright Vessel is a lot of things. It is for conditioning beer, dry hopping, storing beer, carbonating beer and serving beer. The Sankey valve makes it a perfect keg for serving. Use it under the bar in your tap room or restaurant. Use it in your kegerator at home. The 4" tri-clamp port makes it easy to clean, too. Additional features include:
    • Sanitary design, no threads or bulkhead fittings
    • Includes a pressure relief valve (60 psi) with pull-ring so you can vent pressure easily
    • 4" tri-clamp cap can be easily removed, allowing you to pull the Sankey valve out for cleaning
    • Easily fill straight from your Sabco Fermenter
    • Lightweight, 33 pounds
    • 1/2 bbl keg is certified for correct volume to help you comply with regulations
    • Easy to add a Carb Wand (sold separately) to the 1/2 bbl Sabco Bright
    • Made of 304 SS
    • Vessel has a safety burst disk on the bottom dome for your protection in case of accidental high pressure
    • 1/2" tri-clamp port included
  • Sabco Carb Wand

    $95.00$130.00
    This is the best way to carbonate using your Sabco Bright vessels. You can also turn your Sabco Fermenter into a Bright tank. The Carb Wand can be inserted into your Sabco Fermenter or Bright using the 3/4" tri-clamp port in the top. Then, connect a bottle of COfor carbonating or oxygen for aerating. The 0.5 micron stone on the Carb Wand will get the job done quickly. For older Sabco Fermenters without the tri-clamp ports in the cap, purchase this Carb Wand along with the new Fermenter cap (see link below). Made of 304 SS. Includes shut-off valve and brass 5/16" barb.