[wcas-search-form]

  • Close any 1.5" tri-clamp ferrule with this clamp. Made of 304 SS. Kit contains:
    • Two 1.5" tri-clamp caps
    • Two 1.5" buna gaskets
  • This is a package of 3 buna gaskets for tri-clamps. Use these gaskets to fit ferrules with 2" OD. This ferrule size is commonly used with both 1" and 1.5" ID tri-clamp fittings. These are the very same gaskets you will find on BrewMagic equipment with thermometer connections. Sold in packages of 3. For example, ordering quantity of 2 will give you 6 gaskets.
  • This kit includes 2 heavy-duty 1.5" tri-clamps along with 2 FDA approved buna gaskets. This size fits 1.5" tri-clamp ferrules with 2" outside diameter.
  • These are band new, drop-in, D-system, twin-lug American Sankey beer keg valves. They come equipped with o-ring. Keep a few of these backup valves on hand to minimize out-of-service kegs.
    These are 1/2 barrel (15.5 gal) standard keg length (21.75") but can be cut down to fit smaller capacity kegs.
    Sold in packages of 10 valves. For example, ordering a quantity of 2 will give you 20 valves.
  • This is a package of 5 buna gaskets for tri-clamps. Choose size 1/2" or 3/4" ID hose sizes below. These are the very same gaskets that you will find on most tri-clamp connections on Sabco equipment.
  • Use this to connect any 1/2" threaded male outlet to your 1/2" ID hose. Perfect for connecting most pump motors. Made of 304 SS. Includes adapter and SS hose clamp.
  • Close any 1/2" or 3/4" tri-clamp ferrule with this cap. Made of 304 SS. Kit contains:
    • 2 tri-clamp caps
    • 2 buna gaskets
  • Sabco jet burners are not messing around. This burner is rated at 60,000 BTU. It measures 5 5/8" in diameter, weighs 2.6 pounds and has a built-in bracket for adapting igniters. Gas pipe connection is 3/8" NPT. Designed for low pressure. Natural gas supplies are typically already low pressure but bottled propane will need to be regulated below 11" water column for these burners.  
  • This stainless steel lid can be used as a replacement for any BrewMagic V350 system vessel. In fact, it will fit any 12" diameter opening.
  • It's always a good idea to have spare parts on hand. See links below for these other PlatePro parts. These plates are sold in packages of 2. For example, ordering quantity 1 will give you 2 plates.
  • It's always a good idea to have spare parts on hand. See links below for these other PlatePro parts. These plates are sold in packs of 2. For example, ordering quantity 1 will give you 2 plates.
  • Sabco jet burners are not messing around. This burner is rated at 120,000 BTU. It measures 8" in diameter, weighs 4.6 pounds and has 2 types of built-in brackets for adapting igniters. Gas pipe connection is 1/2" NPT. Designed for low pressure. Natural gas supplies are typically already low pressure but bottled propane will need to be regulated below 11" water column for these burners.
  • This is a complete Tri-Clamp assembly for performing your own installation of a 4" sanitary port on any vessel. Includes:
    • 4" tri-clamp long ferrule, 304 SS
    • 4" tri-clamp with heavy turn bolt, 304 SS
    • 4" tri-clamp cap, 304 SS
    • 4" buna tri-clamp gasket
  • 4″ Sankey Tri-Clamp Cap

    $110.00$135.00
    Easily convert your 4" tri-clamp storage vessels to a standard D-system Sankey for simply cleaning or dispensing. This specially designed cap allows inspection of the interior with the simple removal of the tri-clamp. Take advantage of the convenient Sankey valve and then quickly extract the entire valve assembly to easily clean the inside. Important Note: A PRV (pressure relief valve) is needed for your coupler or tank. Serious personal injury may result if your pressure vessel does not include this.
  • This 4" tri-clamp cap can be used to upgrade an older Sabco Fermenter to the current design. Two sanitary ports in the cap give you lots of options. On our Sabco Fermenter we use one for blow-off. The other port can be used to inject oxygen or COwith our Carb Wand. This lets you use your fermenter as a bright tank. Pro tip: Get this cap along with the Carb Wand and Dirty Gauge (links below) to carbonate very quickly right inside your fermenter or bright tank. This cap also includes 2 tri-clamps, 2 caps and 2 gaskets.
  • This is a package of 3 buna gaskets for 4" tri-clamps. These are the gaskets Sabco uses on products such as PubJug, Sabco Fermenters and Sabco Bright Vessels Sold in packages of 3. For example, ordering quantity of 2 will give you 6 gaskets.
  • This kit includes a 4" tri-clamp and a buna gasket. Clamp is solid 304 SS with a heavy-turn bolt.
  • It's always a good idea to have spare parts on hand. See links below for these other PlatePro parts. These plates are sold in packs of 6. For example, ordering quantity 1 will give you 6 plates.
  • 8" Tri-Clamp Buna Gasket. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order of this item.
  • 8" Tri-Clamp compatible cap. All stainless. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order of this item.
  • 8" Tri-Clamp. All stainless. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order for clearance items.
  • 8" Tri-Clamp Compatible Long Ferrule. All stainless. We have surplus inventory of this item so it's marked way down. Price does not include freight. Call or email for a discounted freight quote based upon your total order of this item.
  • This is a swivel adapter to connect a 1/2" hose to any 1/2" male pipe thread (NPT). Use it to connect a hose to the inlet or outlet of a pump with 1/2" MIP inlet or outlet threads. The large grip-style nut makes it easy to snug up the adapter by hand without tools. This eliminates the possibility of damaging the o-ring by over-tightening with a wrench. This also allows an easy disconnect for cleaning. Kit contains one adapter (grip & tailpiece), o-ring, and hose clamp.
  • This is an adapter to connect a 1/2" hose to any 1/2" female pipe thread (NPT). Kit contains one adapter and one hose clamp.
  • This adapter will help you convert the threaded fittings on your pump to sanitary tri-clamp. Once you have converted your pump to tri-clamp fittings you'll be able to easily connect and disconnect your hoses. Package of 1 adapter. We know the picture shows 2 but they are sold individually.
  • This adapter will fit a 1/2" female NPT connection and convert it to tri-clamp. Easily connect and disconnect hoses once you convert. Adapters are sold individually.
  • Use this adapter to modify the female end of a Micromatic shut-off valve to accept your 1/2" tri-clamp hoses. It is also perfect for adding a shut-off valve between two tri-clamp hoses. American D-system keg couplers and shut-off valves utilize a special non-standard thread size. A specific adapter is needed to convert the special thread for use with tri-clamp fittings.
  • Use this adapter to modify a keg coupler to accept your 1/2" tri-clamp hoses. Includes tailpiece and black buna gasket. American D-system keg couplers and shut-off valves utilize a special non-standard thread size. A specific adapter is needed to convert the special thread for use with tri-clamp fittings.
  • These adapters are perfect for making any 3/4" to  1=1/2" TC connection
  • Use this adapter to connect any 1/2" or 3/4" tri-clamp to the male end of a garden hose. Use your imagination. This could be handy for connecting a garden hose to just about every Sabco vessel and fitting.
  • Get a better view with out adjustable-angle tri-clamp thermometer.  It's adjustable from straight angle all the way to a 60° angle. Features include:
    • Large 3″ dial with bold, bright characters for easy reading
    • Case, bezel and stem in 304 SS
    • Tri-clamp connection in your choice of either 3/4" or 1.5"
    • F° & C° in bold easy-to-read numerals
    • Solid metal construction with stainless probe
    • Hermetically sealed glass lens
    • Easy calibration using screw on back of dial body
    • Accuracy of +/- 1% of full scale
    • Tri-clamp gasket included
  • This is a set of couplers for ball-lock Corney kegs. Two types are available: threaded and barbed. The barb type will fit any standard 1/4" ID tubing. Simply use a hose clamp. The threaded type, though, is easier to disconnect. Couplers are sold in sets of two as shown in the photo. You’ll get the liquid-out and the gas-in coupling.
  • Designed for use with household natural gas pressure this cast-iron banjo style burner will produce approx. 30,000 Btu of heating energy. Perfect for your 10-30 gallon mash tun or outdoor cooking. This unit comes with a standard natural gas orifice but can be exchanged for an LP gas orifice. Choose option above. Be advised that when using bottle LP gas that you will need a regulator that will reduce inlet pressure to approx. 11" WC (water column) for best combustion efficiency.
    • 9.2" overall length without orifice
    • 6" burner diameter
    • 4 lbs. cast iron
    • Bracket screw located on the center back side
    • Orifice has 3/8" brass elbow flared connection to fit most gas supply hosing
    • Variable air-mix vent which is used to tune the incoming air and adjust for the most efficient flame
  • This bleeder valve helps you easily prime your magnetic drive pump. Use the bleeder valve to vent air trapped in the hose on the inlet side of the pump. Sabco includes this valve with each ChillWizard chilling system. We didn't always include it, though, so if you have an older ChillWizard, this is a great upgrade. Made of stainless steel. See link below to order high-temperature silicone tubing to connect boil kettle to pump.
  • BrewMagic® Pilot RIMS System

    $7,200.00$9,200.00
    Have questions or need info on any of our great BrewMagic brewing systems?   Contact Matt directly at (419) 345-8290, via call or text, and he can assist with anything you may need to get started. BrewMagic Pilot is available in electric or gas. Choose your size - 20 gallons or 30 gallons. It's still built on the tried-and-true BrewMagic platform but we have gone all stainless, increased batch capacity, boosted the pump and enlarged the touch-screen. The system is ideal for:
    • Serious home brewers
    • Friends who brew together and each want to keep 10 or 12 gallons
    • Pilot brewing and recipe development
    • Nano brewery startups
    • College and university brewing science programs
    Insanely high quality and repeatability have been our claim to fame for almost 30 years. We produced the first commercial-grade RIMS system and have thousands of BrewMagic™ systems in service around the world. Our reputation precedes us, so you can understand why we were so careful about introducing this new system. Our goal was to increase capacity and add features without sacrificing anything. BrewMagic™ Pilot is the result.
    • RIMS (recirculating infusion mash system)
    • All-stainless construction
    • 3-vessel design – Hot liquor, mash tun and boil kettle
    • Sanitary, food-grade welding without threaded fittings
    • 80,000 BTU low-pressure jet burners with electronic igniters
    • Tri-clamp fittings, no soft plumbing
    • Precise temperature control without scorching or caramelization
    • Brew 10-25 gallon batch sizes
    • Digital temperature readout on all 3 vessels
    • 7-inch color touch-screen control
    • Powerful March TE pump
    • Sight glass for mash
    • Recipe storage for mash and boil with visual and audible prompts
    • Network and WiFi capable
    If you’d prefer a full written quote from one of our brewing experts click here to customize your system or call 419-531-5347 to speak with a brewing system expert today.
       
  • Call or text Matt directly at 419-345-8290 with questions.
    BrewMagic Pilot is a 56-gallon system built on the tried-and-true BrewMagic platform. We have gone all stainless, increased batch capacity, boosted the pump and enlarged the touch-screen. The system is ideal for:
    • Startup breweries
    • Brewpubs
    • Pilot brewing and recipe development
    • Nano brewery startups
    • College and university brewing science programs
    Insanely high quality and repeatability have been our claim to fame for almost 30 years. We produced the first commercial-grade RIMS system and have thousands of BrewMagic™ systems in service around the world. BrewMagic® Pro includes the following features:
    • RIMS (recirculating infusion mash system)
    • All-stainless construction
    • 3-vessel design – Hot liquor, mash tun and boil kettle
    • Sanitary, food-grade welding without threaded fittings
    • 80,000 BTU low-pressure jet burners with electronic igniters
    • Tri-clamp fittings, no soft plumbing
    • Precise temperature control without scorching or caramelization
    • Brew 10-50 gallon batch sizes
    • Digital temperature readout on all 3 vessels
    • 7-inch color touch-screen control
    • 2 powerful March TE pumps
    • Sight glass for mash
    • Recipe storage for mash and boil with visual and audible prompts
    • Network and WiFi capable
     
  • You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
  • This is a replacement carbonation stone for use with the Sabco Carb Wand. Porous metal design  .005  (1/2 micron) 1/8" FIP connection Made of 304 SS
  • ChillWizard System

    $990.00$1,090.00
    The ChillWizard system includes everything you need for pumping, chilling and oxygen injection all in one compact, portable unit. High efficiency. Easy cleaning. You'll love it. Features include:
    • Clean in place using the pump
    • Diffusion stone to inject oxygen as wort flows through the chiller
    • Thermometer on the exit side displays wort temperature
    • Adjustable flow rate
    • Pump is capable of sending wort uphill to your fermenter
    • Easily disassembled for periodic deep clean
    • Easily reverse flow through plate chiller for backflushing
    • All built on a compact frame with handle
    • GFCI plug for safety in wet environments
  • This LP hose will connect your propane bottle to your BreMagic system. It includes a 1/4" NPT male thread for connecting to the regulator on your BrewMagic V350 system. The other end connects to 20-pound North American LP bottles. Please note this hose will not work with most LP bottles outside North America.
  • These Federal Warning labels are required by law and have been approved for use on beer kegs nationally. We use an incredibly strong adhesive for stainless application and a thick laminated surface. These stay put even in harsh caustic conditions. 3 3/8" x 1 7/16" with black text on white background. Sold in packages of 50. For example, ordering a quantity of 2 will give you 100 labels.
  • This GFCI plug is a safety device, perfect for wet environments. If you have a pump or electric heater being used, it's a good idea to plug it into a GFCI receptacle or use this plug. This plug is rated for 120 Volts, 15 Amps and includes a ground. This plug is the American, grounded, 3-prong version. We use it in our ChillWizard system.
  • This is a set of burner orifices for previous versions of BrewMagic with high pressure cast burners as shown in the photo below. This is a set of 3 orifices. These are designed for use with high pressure cast burners only as seen in photo (3/8" Flare x 1/8" MIP elbow). The style of these may vary but the thread sizes do not change. Each orifice is designed specifically for use with propane. High pressure propane sources must be regulated not to exceed 15 psi manifold inlet pressure. High-Pressure-Burner-for-BM If you need orifices for high pressure natural gas, please order this item and submit a note with your order. The note should request Sabco drill out the orifices for natural gas.
  • This coupler will attach to any US Micromatic keg coupler. It will fit either the gas or beer side. Includes the hose barb, coupler nut and gasket Typically, you will want to choose 3/8" for the gas side and 1/2" for the beer side.
  • This adapter will help you connect hose to a threaded ball-lock coupler. Better than hose barbs which distort the hose and leave pockets that are very difficult to clean. Use ball-lock couplers, instead. Kit includes the adapter and a stainless steel hose clamp.
  • This keg coupler works with virtually all American keg valves. Commonly known as D-system. Features include:
    • Stainless steel body for durability and resistance to chemicals
    • Stainless steel handle fork for strength
    • Tin/nickel plated probe is resistant to chemicals and won't chip like chrome
    • Short handle is ideal for 1/2 bbl and 1/6 bbl kegs
    • Includes built-in pressure relief valve (55-65 psi)
    • Includes 3/8" barb for gas port (fits 5/16" ID gas hose)
    • Industry standard beer port
     
  • This ball valve has a keg coupler thread and is used to stop beer flow from a standard keg coupler. This thread will not fit a 1/2" outlet.
  • You probably got a great deal on those used kegs but wouldn't you like to get rid of the name engraved in the dome? Use these labels to cover the engraved name. We make the silver crescents labels using the very same heavy-duty, laminated finish and adhesive that is used for permanent federal warning labels. They are also UV resistant and extremely durable. They can endure heat and cold as well as the caustics and other chemicals. Sold in packages of 100. For example, ordering a quantity of 2 will give you 200 keg engraving shields.