• SABCO’s Dual “Step-Down” regulator is ideal for using the same CO2 source to deliver different pressures to two different target vessels.  Use the first gauge to apply pressure to move product from your source vessel while using the second gauge to apply back pressure to your target vessel.
    Add to cart Details
  • This conversion kit is for use with Brew-Magics which are CSA certified and have been designed for use with low-pressure, banjo style burners only.  This is not for use with the the 2X model Brew-Magic which uses jet style burners. It is also not for use with high-pressure systems. The low-pressure, appliance-rated regulator is specific for this conversion and must be used. Likewise, the orifices included with this conversion kit, must replace your current LP type orifices. Quick connector and 10 foot NG-rated hosing is included per the photo / diagram.
    Select options Details
  • This assembly is for use with Brew-Magics which have been designed for use with low-pressure banjo style burners (Series CSA-2011) only. Not for use with high-pressure systems. This is also not for use with the the 2X model Brew-Magic which uses jet burners. The low pressure, appliance-rated regulator is specific for this conversion and must be used. Likewise, the orifices included with this conversion kit, are specific and must replace your current NG type orifices. Connector plumbing and four feet LP rated hosing are included.  See the attached diagrams.
    Select options Details
  • Select options Details
  • Upgrade your SABCO fermenters to the latest sanitary design!
    Add to cart Details
  • Chose from two connector variations.  The 'Dirty' Gauge by SABCO is easily connected to either a Micromatic coupler (tapper) thread, or to any 1/2" Tri-Clamp.  Choose the variation appropriate for your vessel. Read from 0 to 60psi. Perfect for tuning carbonation levels or for general pressure reading. Includes gauge, your choice of connector. The coupler thread option includes the gasket for the threaded nut. The Tri-Clamp option does not include a 1/2" tri-clamp gasket or clamp.
    Select options Details
  • Select options Details
  • Oxygen Stone Assembly

    $69.00$129.00
    The Oxygen Stone Assembly is a brilliant tri-clamp connector to your wort flow.  Find it in SABCO's famous Chill-Wizard System. This is the replacement assembly for Chill-Wizard.  Diffuse a 0.5 micron foam layer of O2 into the wort stream.
    Select options Details
  • This assembly is for use with Brew-Magic Systems which have been designed for use with high-pressure propane burners only. It comes equipped for direct connection to the Brew-Magic’s gas manifold inlet. The adjustable regulator can modify inlet pressure from 5-15psi. Unregulated, normal high pressure from propane tanks is 150 psi. The green nut will connect to the external thread of common US propane tanks.
    Add to cart Details
  • Banjo 10" burner. Perfect for Boil kettle or HLT
    Select options Details
  • The Brew-Magic burner orifice (jet) is the opening into the burner casting from the regulated gas manifold. It's designed to control the flow pressure of the incoming fuel. This is a complete set of three gas orifices. CAUTION:  These are designed for use with High Pressure cast burners only as seen in photo.  ( 3/8" Flare x 1/8" MIP elbow ). The style of these may vary however the thread sizes do not change. Each orifice is designed specifically for use with either propane (LP) or natural gas (NG). High pressure propane sources must be regulated not to exceed 15psi. manifold inlet pressure. Choose the fuel gas type that you intend to use in the options below.
    Select options Details
  • Add to cart Details
  • Add to cart Details
  • Banjo 6" burner. Perfect for your Mash kettle or any outdoor cooking.
    Select options Details
  • SABCO uses an excellent pull-ring type pressure-relief valve (PRV) Details below.
    Add to cart Details
  • SABCO chooses only brewer's hardware which is designed for heavy duty handling in the professional brewing environment. Use this barb with common 3/8"ID, hosing when you need to connect to a vessel that has sanitary 1/2"OD tube size with 1/2"- 3/4" tri-clamp ferrule connections.  SABCO often uses a dual regulator to push CO2 to either a fermenter or bright beer vessel.  This fitting can be attached to the end of the regulator hose which will allow easy connection to any sanitary Tri-clamp valve or fitting. ( 1 pc per Pkg. )  
    Add to cart Details
  • This coupler nut, gasket and tailpiece combination can be attached to any US Micromatic keg coupler. It will fit either the gas or beer side thread. Choose the size you need below. Each kit will contain the barb of your choice along with the standard keg coupler nut and gasket.
    Select options Details
  • 1/4" Barb x Ball-Lock Coupler.  Use this adapter to connect a threaded flare type Corney Ball-Lock coupler to any 1/2" ID hose or tubing.  Kit includes one adapter and stainless hose clip
    Add to cart Details