This GFCI plug is a safety device, perfect for wet environments. If you have a pump or electric heater being used, it's a good idea to plug it into a GFCI receptacle or use this plug. This plug is rated for 120 Volts, 15 Amps and includes a ground. This plug is the American, grounded, 3-prong version. We use it in our ChillWizard system.
This is a set of burner orifices for previous versions of BrewMagic with high pressure cast burners as shown in the photo below. This is a set of 3 orifices. These are designed for use with high pressure cast burners only as seen in photo (3/8" Flare x 1/8" MIP elbow). The style of these may vary but the thread sizes do not change. Each orifice is designed specifically for use with propane. High pressure propane sources must be regulated not to exceed 15 psi manifold inlet pressure. If you need orifices for high pressure natural gas, please order this item and submit a note with your order. The note should request Sabco drill out the orifices for natural gas.
This tri-clamp, sanitary thermowell can be used in place of the standard dial thermometer on your Sabco fermenter. Insert a temperature probe into the thermowell and connect it to a temperature controller. The thermowell connects easily to our Sabco fermenter. Just remove the tri-clamp thermometer and attach this. Specifications:
- Connects via 1.5" tri-clamp
- Will accept any type of probe with maximum OD of 1/4"
- Made of 304 SS
- Tube length is 9.25"
This is the RTD temperature sensor used on all current BrewMagic systems. It was also used on V350 systems beginning in 2013. RTD sensors provide accurate temperature data to digital controllers such as those used on BrewMagic systems. These RTD sensors have the following specifications:
- Made of 304 SS
- 100 ohms
- 3-wire design for increased accuracy
- 1/4" diameter
- 3" probe length
- Relief spring at probe to prevent damage
- 12 feet of armored cable for durability in harsh environments
Do you have a false bottom in your BrewMagic V350 kettle? Consider converting to a whirlpool siphon. It's easy to manually create a whirlpool in the small kettle on a BrewMagic V350 system if you have this tri-clamp siphon. After knockout, rotate your spoon around the perimeter of the kettle to turn the wort and create a cone of trub. You'll leave that stuff behind instead of clogging up your ChillWizard or transferring it to your fermenter. Made of 304 SS and sanitary welded with a tri-clamp connection.
Get a better view with out adjustable-angle tri-clamp thermometer. It's adjustable from straight angle all the way to a 60° angle. Features include:
- Large 3″ dial with bold, bright characters for easy reading
- Case, bezel and stem in 304 SS
- Tri-clamp connection in your choice of either 3/4" or 1.5"
- F° & C° in bold easy-to-read numerals
- Solid metal construction with stainless probe
- Hermetically sealed glass lens
- Easy calibration using screw on back of dial body
- Accuracy of +/- 1% of full scale
- Tri-clamp gasket included
This is a stainless steel type-J thermocouple temperature sensor. It was used on BrewMagic V350 systems until 2013. If you are purchasing this as a replacement for the temperature sensor on your BrewMagic V350 system, please look carefully at what you currently have. If your temperature sensor has 2 wires, purchase this thermocouple. If your sensor has 3 wires, then you need to replace it with an RTD temperature sensor which can also be found on this site.
Brewer hose with tri-clamp fittings included. Don't purchase them all separately like some sort of fool. This hose is 5 feet long and allows you to make a quick, sanitary connection between tri-clamp components. We pre-assemble everything for you with brewer hose, tri-clamp ferrules, stainless steel hose clamps, tri-clamps and gaskets. You'll save money by buying these components as a kit.
This kit allows you to fill your Corney keg with beer from your fermenter without opening the top port and risking contamination. Beer will fill your Corney keg from the bottom up through the dip tube on the liquid out side. The kit includes everything shown in the picture except the hose The hose is pictured in order to demonstrate the connections. Hose can be purchased separately. See link below. If you are ready to upgrade from Corneys, see our link below for PubJug.
This is a 0.5 micron stone assembly to aerate your wort as it enters the fermenter. The end of the stone is threaded for easy removal and cleaning. Tri-clamp ready for easy removal and sanitary connection. Sabco uses this assembly on its famous ChillWizard system. This assembly is available in two ways:
- Stone assembly with tri-clamp connection
- Complete assembly with 1/4" brass barb along with the inline shut-off valve
The Dirty Gauge was invented by Steve Acord at Dirty Bucket Brewing Company in Woodinville, WA. This brilliant product accurately reads pressure during the carbonation process. You can attach the Dirty Gauge directly to the top of your Sabco Fermenter. Use this in conjunction with our carbonation stone and speed up the process considerably. Two options are available. The coupler thread option includes the gasket for the threaded nut. The tri-clamp option does not include a 1/2" tri-clamp gasket or clamp.
Silicone tubing is ideal for high temperatures. This tubing is rated for -100°F to 500°F. Perfect for moving wort out of your boil kettle. Meets FDA standards and is tasteless and odorless. Available in 1/2" and 3/4" ID. Tubing is sold in lengths of 10 feet. For example, ordering a quantity of 2 will give you 20 feet. Other specifications:
- Working pressure up to 10 psi
- Odorless, tasteless and inert
- Good insulating properties
- Resists deterioration from ultraviolet light
- NSF 51 listed
Built to Sabco specifications, this sight glass is durable and sanitary. Notice the thickness of top and bottom plates. Easy to take apart for cleaning. Available as either sight glass only or as a kit designed to retrofit older BrewMagic V350 models that used a plastic tube as sight glass on mash inlet. Use with any 1/2" or 3/4" tri-clamp connection. Specifications:
- Made of 304 SS
- Overall length = 4.5"
- Diameter = 2.25"
- Tube diameter = 3/4"
- Sabco sight glass
- Tri-clamp elbow
- 2 TC clamps with gaskets
- 1/2"OD compression union
This 4" tri-clamp cap can be used to upgrade an older Sabco Fermenter to the current design. Two sanitary ports in the cap give you lots of options. On our Sabco Fermenter we use one for blow-off. The other port can be used to inject oxygen or CO2 with our Carb Wand. This lets you use your fermenter as a bright tank. Pro tip: Get this cap along with the Carb Wand and Dirty Gauge (links below) to carbonate very quickly right inside your fermenter or bright tank. This cap also includes 2 tri-clamps, 2 caps and 2 gaskets.
This is the best way to carbonate using your Sabco Bright vessels. You can also turn your Sabco Fermenter into a Bright tank. The Carb Wand can be inserted into your Sabco Fermenter or Bright using the 3/4" tri-clamp port in the top. Then, connect a bottle of CO2 for carbonating or oxygen for aerating. The 0.5 micron stone on the Carb Wand will get the job done quickly. For older Sabco Fermenters without the tri-clamp ports in the cap, purchase this Carb Wand along with the new Fermenter cap (see link below). Made of 304 SS. Includes shut-off valve and brass 5/16" barb.
Easily convert your 4" tri-clamp storage vessels to a standard D-system Sankey for simply cleaning or dispensing. This specially designed cap allows inspection of the interior with the simple removal of the tri-clamp. Take advantage of the convenient Sankey valve and then quickly extract the entire valve assembly to easily clean the inside. Important Note: A PRV (pressure relief valve) is needed for your coupler or tank. Serious personal injury may result if your pressure vessel does not include this.
Sabco jet burners are not messing around. This burner is rated at 60,000 BTU. It measures 5 5/8" in diameter, weighs 2.6 pounds and has a built-in bracket for adapting igniters. Gas pipe connection is 3/8" NPT. Designed for low pressure. Natural gas supplies are typically already low pressure but bottled propane will need to be regulated below 11" water column for these burners.
Sabco jet burners are not messing around. This burner is rated at 120,000 BTU. It measures 8" in diameter, weighs 4.6 pounds and has 2 types of built-in brackets for adapting igniters. Gas pipe connection is 1/2" NPT. Designed for low pressure. Natural gas supplies are typically already low pressure but bottled propane will need to be regulated below 11" water column for these burners.
You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
Stainless steel chamber for low-density heating element. No threads. All sanitary welding by the best welders around. Constructed of 304 SS, 15.13"L, 1.38"ID, 1.5" tri-clamp connection. Wort in/out tubing is 0.5"OD. Heating element sold separately. See link below.
This is the famous March 815 pump with stainless steel housing. The stainless housing is more rugged and rated for 250° F. The larger magnet and impeller design results in higher flow and makes priming easier. Sabco uses this pump on its ChillWizard system. This pump includes a cord but not a plug.
This is the famous March 815 pump with a GFCI plug added. Rated for boiling temperatures. Includes rugged stainless steel pump housing and built-in bracket, 38" cord and GFCI plug. The March 815 has a larger impeller than most wort pumps which makes it easier to prime and avoids cavitation. Specifications:
- 115 V AC
- 1/25 Hp
- Magnetic drive
- Ryton impeller
- Encapsulated ceramic magnet
- Ceramic shaft
- thrust bearings
- Viton o-ring gasket
- 316 SS hardware
- Open fan cooled
- Rated for liquid temperatures up to 250° F
This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from natural gas (NG) to propane (LP). Kit includes everything shown in the photo. There are several things to consider before ordering:
- Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
- This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
- This is not for use with any high-pressure burner systems.
- Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.