Electric Components

//Electric Components
  • This is the famous March 815 pump with a GFCI plug added. Rated for boiling temperatures. Includes rugged stainless steel pump housing and built-in bracket, 38" cord and GFCI plug. The March 815 has a larger impeller than most wort pumps which makes it easier to prime and avoids cavitation. Specifications:
    • 115 V AC
    • 1/25 Hp
    • Magnetic drive
    • Ryton impeller
    • Encapsulated ceramic magnet
    • Ceramic shaft
    • thrust bearings
    • Viton o-ring gasket
    • 316 SS hardware
    • Open fan cooled
    • Rated for liquid temperatures up to 250° F
  • This is the famous March 815 pump with stainless steel housing. The stainless housing is more rugged and rated for 250° F. The larger magnet and impeller design results in higher flow and makes priming easier. Sabco uses this pump on its ChillWizard system. This pump includes a cord but not a plug.
  • You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
  • This heating element is designed to fit the BrewMagic RIMS heat chamber. It's made of stainless steel and connects with a tri-clamp. Use this as a replacement for any BrewMagic heater that has the tri-clamp design. It's easy to clean, has a large surface area for low wattage density and the tri-clamp makes it easy to disconnect. We also include a removable electric plug as shown in the picture. Low wattage density means you don't scorch your wort. No caramelization as long as you keep your wort moving.
  • Out of stock
    This is a replacement heating element for older BrewMagic systems. The model available on this page screws into the heat chamber. Do not order this model if you have anything other than an old BrewMagic system with this style heater. Also, be sure to measure your heat chamber. Only order this model if it is at least 13 7/8".
  • This is a stainless steel type-J thermocouple temperature sensor. It was used on BrewMagic V350 systems until 2013. If you are purchasing this as a replacement for the temperature sensor on your BrewMagic V350 system, please look carefully at what you currently have. If your temperature sensor has 2 wires, purchase this thermocouple. If your sensor has 3 wires, then you need to replace it with an RTD temperature sensor which can also be found on this site.
  • This is the RTD temperature sensor used on all current BrewMagic systems. It was also used on V350 systems beginning in 2013. RTD sensors provide accurate temperature data to digital controllers such as those used on BrewMagic systems. These RTD sensors have the following specifications:
    • Made of 304 SS
    • 100 ohms
    • 3-wire design for increased accuracy
    • 1/4" diameter
    • 3" probe length
    • Relief spring at probe to prevent damage
    • 12 feet of armored cable for durability in harsh environments
    This RTD (resistance temperature detector) provides accurate and stable information to your V350 Brew-Magic controller.  This will replace the existing one in your Brew-Magic System If you are purchasing this as a replacement for the temperature sensor on your BrewMagic, please look carefully at what you currently have. If your temperature sensor has 3 wires, purchase this RTD. If your sensor has 2 wires, then you need to replace it with a type-J thermocouple which can also be found on this site.
  • This GFCI plug is a safety device, perfect for wet environments. If you have a pump or electric heater being used, it's a good idea to plug it into a GFCI receptacle or use this plug. This plug is rated for 120 Volts, 15 Amps and includes a ground. This plug is the American, grounded, 3-prong version. We use it in our ChillWizard system.