• This is a package of 3 buna gaskets for tri-clamps. Use these gaskets to fit ferrules with 2" OD. This ferrule size is commonly used with both 1" and 1.5" ID tri-clamp fittings. These are the very same gaskets you will find on BrewMagic equipment with thermometer connections. Sold in packages of 3. For example, ordering quantity of 2 will give you 6 gaskets.
  • This is a package of 5 buna gaskets for tri-clamps. Choose size 1/2" or 3/4" ID hose sizes below. These are the very same gaskets that you will find on most tri-clamp connections on Sabco equipment.
  • This stainless steel lid can be used as a replacement for any BrewMagic V350 system vessel. In fact, it will fit any 12" diameter opening.
  • Get a better view with out adjustable-angle tri-clamp thermometer.  It's adjustable from straight angle all the way to a 60° angle. Features include:
    • Large 3″ dial with bold, bright characters for easy reading
    • Case, bezel and stem in 304 SS
    • Tri-clamp connection in your choice of either 3/4" or 1.5"
    • F° & C° in bold easy-to-read numerals
    • Solid metal construction with stainless probe
    • Hermetically sealed glass lens
    • Easy calibration using screw on back of dial body
    • Accuracy of +/- 1% of full scale
    • Tri-clamp gasket included
  • You broke your BrewMagic V350 touch-screen?!?! Fear not... Smashing or cracking your touch-screen is not covered by warranty but we offer a service to replace the screen so you don't need to purchase a brand new controller. Simply purchase the repair service from this page and send us your V350 controller. We'll replace the screen and send it back to you within a few days.
  • This LP hose will connect your propane bottle to your BreMagic system. It includes a 1/4" NPT male thread for connecting to the regulator on your BrewMagic V350 system. The other end connects to 20-pound North American LP bottles. Please note this hose will not work with most LP bottles outside North America.
  • This is a set of burner orifices for previous versions of BrewMagic with high pressure cast burners as shown in the photo below. This is a set of 3 orifices. These are designed for use with high pressure cast burners only as seen in photo (3/8" Flare x 1/8" MIP elbow). The style of these may vary but the thread sizes do not change. Each orifice is designed specifically for use with propane. High pressure propane sources must be regulated not to exceed 15 psi manifold inlet pressure. High-Pressure-Burner-for-BM If you need orifices for high pressure natural gas, please order this item and submit a note with your order. The note should request Sabco drill out the orifices for natural gas.
  • This is the famous March 815 pump with stainless steel housing. The stainless housing is more rugged and rated for 250° F. The larger magnet and impeller design results in higher flow and makes priming easier. Sabco uses this pump on its ChillWizard system. This pump includes a cord but not a plug.
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from natural gas (NG) to propane (LP). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • This kit will help you convert your low-pressure, CSA-certified BrewMagic V350 system gas type from propane (LP) to natural gas (NG). Kit includes everything shown in the photo. There are several things to consider before ordering:
    • Only purchase this to retrofit BrewMagic V350 systems which are CSA certified and designed for low-pressure, banjo-style burners.
    • This is not for use with BrewMagic 2X, BrewMagic XL, BrewMagic Pilot or BrewMagic Pro.
    • This is not for use with any high-pressure burner systems.
    • Look closely at the photos to determine if you have elbow or straight orifices. Sabco begain using straight orifices in August, 2014.
  • This is the pump we used on BrewMagic systems for many years but it has been discontinued and we can no longer get them. Our recommended replacement is the March 815 High Temperature Pump.  The motor is identical but the volute is much better. It is rated for high temperature and it's made of stainless steel. The recommended replacement pump will require some plumbing on your part to make the hoses fit. Please be aware this is not a drop-in replacement for very old BrewMagic pumps. To determine which style pump is on your BrewMagic system, take a close look at the arrangement of the hose fittings and compare it to the pictures on this site.
  • Food-grade 3/8" ID tubing designed for beverage use. Very easy to clean. Not approved for boiling temperatures. Tubing is sold in lengths of 10 ft. Example: to buy 20 feet, order a quantity of 2. Great for use as a blowoff tube on your fermenter.
  • Stainless steel chamber for low-density heating element. No threads. All sanitary welding by the best welders around. Constructed of 304 SS, 15.13"L, 1.38"ID, 1.5" tri-clamp connection. Wort in/out tubing is 0.5"OD. Heating element sold separately. See link below.
  • This is the RTD temperature sensor used on all current BrewMagic systems. It was also used on V350 systems beginning in 2013. RTD sensors provide accurate temperature data to digital controllers such as those used on BrewMagic systems. These RTD sensors have the following specifications:
    • Made of 304 SS
    • 100 ohms
    • 3-wire design for increased accuracy
    • 1/4" diameter
    • 3" probe length
    • Relief spring at probe to prevent damage
    • 12 feet of armored cable for durability in harsh environments
    This RTD (resistance temperature detector) provides accurate and stable information to your V350 Brew-Magic controller.  This will replace the existing one in your Brew-Magic System If you are purchasing this as a replacement for the temperature sensor on your BrewMagic, please look carefully at what you currently have. If your temperature sensor has 3 wires, purchase this RTD. If your sensor has 2 wires, then you need to replace it with a type-J thermocouple which can also be found on this site.
  • Sight Glass

    $80.00$140.00
    Built to Sabco specifications, this sight glass is durable and sanitary. Notice the thickness of top and bottom plates. Easy to take apart for cleaning. Available as either sight glass only or as a kit designed to retrofit older BrewMagic V350 models that used a plastic tube as sight glass on mash inlet. Use with any 1/2" or 3/4" tri-clamp connection. Specifications:
    • Made of 304 SS
    • Overall length = 4.5"
    • Diameter = 2.25"
    • Tube diameter = 3/4"
    The retrofit kit option includes:
    • Sabco sight glass
    • Tri-clamp elbow
    • 2 TC clamps with gaskets
    • 1/2"OD compression union
  • These are replacement sight glass tubes for the BrewMagic V350 system. These sight glass tubes fit the boil kettle and the HLT. Sold in packages of 2.
  • This is a stainless steel type-J thermocouple temperature sensor. It was used on BrewMagic V350 systems until 2013. If you are purchasing this as a replacement for the temperature sensor on your BrewMagic V350 system, please look carefully at what you currently have. If your temperature sensor has 2 wires, purchase this thermocouple. If your sensor has 3 wires, then you need to replace it with an RTD temperature sensor which can also be found on this site.
  • This is a tri-clamp kit, including 2 clamps and 2 gaskets. Out tri-clamps are heavy-duty and higher quality than a lot of what you'll find out there. Other sizes are available, as well. Look for links below.
  • This is a very high quality thermometer with tri-clamp connection. Features include:
    • Large 3" dial with bold, bright characters for easy reading
    • Case, bezel and stem in 304 SS
    • Tri-clamp connection in your choice of either 3/4" or 1.5"
    • F° & C° in bold easy-to-read numerals
    • Solid metal construction with stainless probe
    • Hermetically sealed glass lens
    • Easy calibration using screw on back of dial body
    • Accuracy of +/-1% of full scale
    • Tri-clamp gasket included
    • Stem length on 1.5" TC version is 1-13/16"
    • Stem length on the 3/4" TC version is 1-5/16"
  • Do you have a false bottom in your BrewMagic V350 kettle? Consider converting to a whirlpool siphon. It's easy to manually create a whirlpool in the small kettle on a BrewMagic V350 system if you have this tri-clamp siphon. After knockout, rotate your spoon around the perimeter of the kettle to turn the wort and create a cone of trub. You'll leave that stuff behind instead of clogging up your ChillWizard or transferring it to your fermenter. Made of 304 SS and sanitary welded with a tri-clamp connection.